Knowing Plumbing Basics is Crucial For Installing a Bathtub
Knowing Plumbing Basics is Crucial For Installing a Bathtub
Blog Article
How do you really feel in relation to How to Install a Bathtub Yourself?
Mounting a bathtub isn't specifically rocket science, however it does call for strong plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old bathtub is easily accessible, the job can move rapidly; if you need to open up a wall to remove the old tub and position the new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as set in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. Instead of hiring a professional to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might need an expert plumber to make tube connections.
This article will aid you set up a new bathtub in your washroom if you have currently gotten a new bathtub and also don't need to transform the arrangement of your previous supply of water pipes.
Your devices as well as material list should comprise the following:
Getting ready for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the required position. The wood boards are handy in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost flexible faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water as well as examine all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub and also examine the overflow electrical outlet and the typical outlet for leakages.
Finally, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has actually been utilized at least once as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in location in between the faucet and also the sink. Safeguard the tap in position with the supplier supplied backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, causing the water to permeate the wall surface between the bathroom and the tiling, leading to problems with moisture and also possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealer can break relatively very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very involved in How to Install a Bathtub Yourself and I am praying you appreciated the new entry. For those who enjoyed our page kindly don't forget to share it. Thank you so much for taking the time to read it.
Expertise at your service. Report this page